HOME > blogy > Outdoor rental LED panels: IP ratings, heat and power

Outdoor rental LED panels: IP ratings, heat and power

Mark the front and rear exposure separately on the stage plan. Matrix 500 outdoor and Lite outdoor specify IP65 on both faces. X-1000 specifies IP65 front and IP54 rear. The crew’s cable route and access behind the wall belong on the same drawing.

Three outdoor rental builds

Venkovní série Přední / zadní Standardní výstup Služby
Matrix 500 IP65 / IP65 4,500 nitů Přední a zadní
X-1000 IP65 / IP54 4,500 nitů Přední
lite IP65 / IP65 3,500 nitů Přední

Select the exact brightness version before requesting peak input and distribution details. Matrix 500 outdoor P3.9 and P4.8 have a separate 6,500-nit configuration. The X-1000 option reaches up to 5,000 nits.

Rear of an assembled X-1000 wall, showing where the crew needs access to connections.
Rear of an assembled X-1000 wall, showing where the crew needs access to connections.

Trace the rear exposure

On a roofed stage, rain can still approach from the open rear or side. Mark the final position of connectors, closures, cable drops and access points. Give the supplier a rear elevation and ask how each interface is protected in the operating configuration.

Open X-1000 power box. Record the electronics and brightness version when requesting electrical data.
Open X-1000 power box. Record the electronics and brightness version when requesting electrical data.

Review heat at the operating point

Describe afternoon sun, show duration and any scenic backing that limits airflow. Request the operating range and electrical sheet for the specific order. Check the assembled screen at the intended brightness during acceptance and agree how the crew will inspect the system between shows.

Mark the rain exposure on a rear elevation

Consider a roofed stage with an open loading side. A roof covers the top of the wall while driven rain may reach the rear connectors. On the rear elevation, draw the prevailing weather direction, cable entry points, service openings and where the crew can inspect them. Mark any planned scenic covering and send the drawing with the outdoor model request.

Na výkresu What to obtain before ordering
Face and rear exposure Supplier confirmation of the exact cabinet’s front and rear ratings and the required assembled connector configuration
Plug entries and closures A photograph or drawing of the specified connectors and caps in their operating positions
Backing and service corridor An approved clearance drawing showing the air path and access with the scenery installed

For the same site, compare X-1000’s IP65 front and IP54 rear with the IP65 front and rear ratings of outdoor Matrix 500 or Lite. Select against the actual rear exposure and approved installation. The cabinet rating alone does not establish that the assembled stage, cabling and power distribution are suitable for that site.

Specify the heat and electrical review

Give engineering the expected air temperature at the wall, the period in direct sun, the show duration and the planned screen brightness. Request the operating limits, ventilation clearance, average and maximum consumption, and the units for the exact SKU and brightness option. An afternoon outdoor rehearsal and an evening show can need different operating settings on the same wall.

If the approved electrical sheet gives maximum consumption in W/m², multiply it by active area to obtain a display-only planning figure. A 6 × 3 m face has 18 m². Leave the watts field open until the correct sheet is attached. The venue electrician needs that figure, the prescribed supply details and the separate equipment loads to plan distribution. Record the agreed configuration and who can approve a change if the scenic backing moves.

Nejčastější dotazy
Does an overhead stage roof settle the choice of outdoor cabinet?
Mark the open sides and back of the stage as well as the roof line. Rain reaching the rear can make the connector configuration important even when the display face sits under cover. Send the rear elevation, cable-entry position and intended exposure to the supplier and obtain approval for the complete operating configuration at that site.
How do I compare IP65 front and IP54 rear with IP65 on both faces?
Write the two ratings in separate columns on the quote. The X-1000 outdoor cabinet has IP65 at the front and IP54 at the rear. Outdoor Matrix 500 and outdoor Lite list IP65 on both sides. Match the rear rating and the specified plugs and closures to the rear exposure shown on your installation drawing.
What thermal information should accompany a request for an outdoor rental wall?
State when direct sun reaches the wall, the expected ambient conditions, the intended brightness and how long the display runs. Attach the scenic backing drawing and service corridor dimensions. Ask engineering to mark the required air path and clearance and to supply the operating limits for the exact cabinet and brightness version being priced.
Which consumption figure belongs on the venue electrical worksheet?
Ask for maximum input for the ordered configuration and record whether the supplier quotes per cabinet or per square metre. For a 6 × 3 m display, multiply an approved per-square-metre figure by eighteen. Keep processing and other equipment on separate lines. Give the underlying sheet and units to the venue electrician reviewing distribution.
What should I check if the rear drape moves closer after the design is approved?
Record the revised distance and draw the new position relative to the connections, service openings and intended airflow. Give the amended elevation to the supplier and venue before using the earlier approval. Update the clearance and service instructions on the crew sheet once the revised arrangement has been reviewed for the planned operating point.
What should the sample inspection show about exposed plugs and spare ports?
Ask for a sample assembled with the same cables, mating plugs and closures listed for your order. Photograph each connection as it will operate, including unused entries and the cable route behind the wall. Keep the supplier’s instructions with those photographs so the incoming crew can inspect the actual arrangement after each rebuild.

Prodiskutujte své požadavky na jas

Řekněte nám, co má obrazovka dělat. Můžeme vám navrhnout konfiguraci čtvercového typu a pro vaši cenovou nabídku potvrdit podrobnosti o jasu a napájení.

Žádost o cenovou nabídku
Pokračovat ve čtení
Přineste nám stručný přehled

Začněte svůj projekt.

Výkres, fotografie staveniště nebo první nápad. Sdělte nám, co plánujete, a proberte detaily s naším technickým týmem.

Tyto údaje používáme k odpovědi na váš projekt. Oznámení o ochraně osobních údajů.